Features of the Concrete Structure of the Structural Element Made by Additive Technology
Abstract
The article discusses the features of the structure of concrete in a structure made using additive technology (3-D printing). The result of the formation of the structure when using the 3-D printing method is investigated. According to the results of experimental studies, the features of the formation of the concrete body of the structure performed using additive technology are revealed.
The features of the concrete structure formed in the concrete body when using additive technology are established. The results obtained can be used in the development of methods for experimental studies of effective mechanical characteristics of concrete, as well as in studies to determine the coefficients of concrete working conditions in structures made using additive technology.
About the Authors
O. V. Kabantsev
Moscow State University of Civil Engineering (National Research University) (MGSU)
Russian Federation
Russian Federation
Oleg V. Kabantsev, Doctor of Technical Sciences, Director of the Directorate of Scientific and Technical Projects, Professor of the Department of Reinforced Concrete and Masonry Structures
Scopus: 15055871000
129337, Moscow, Yaroslavskoe shosse, 26
A. V. Karlin
Moscow State University of Civil Engineering (National Research University) (MGSU)
Russian Federation
Russian Federation
Aleksey V. Karlin, engineer, REC "Geotechnics"
129337, Moscow, Yaroslavskoe shosse, 26
References
1. Naoum S. Factors influencing labor productivity on construction sites. International Journal of Productivity and Performance Management. 2016. Vol. 65(3), pp. 401–421. DOI: 10.1108/IJPPM-03-2015-0045.
2. Nasir H., Ahmed H., Haas C., Goodrum P.M. An analysis of construction productivity differences between Canada and the United States. Construction Management and Economics. 2013, pp. 595–607, 2013. https://doi.org/10.1080/01446193.2013.848995.
3. Reinventing Construction: a route to higher productivity. McKinsey Global Institute analysis. 2017.
4. Mischke J. Reinventing construction: a route to higher productivity. McKinney Global Institute. Construction-tion: Let's build changes! 2017.
5. Paolini A., Kollmannsberger S., Rank E. Additive manufacturing in construction: a review on processes, applications, and digital planning methods. Additive Manufacturing. 2019 Vol. 30. 100894. https://doi.org/10.1016/j.addma.2019.100894.
6. Panda B., Tay Y.W.D., Paul S.C., Tan M.J. Current challenges and future potential of 3D concrete printing: aktuelle Herausforderungen und Zukunftspotenziale des 3D-Druckens bei Beton. Materialwissenschaft und Werkstofftechnik. 2018 Vol. 49 (5), pp. 666–673. DOI: 10.1002/mawe.201700279.
7. Wangler T., Roussel N., Bos F.P., Salet T.A.M., Flatt R.J. Digital concrete: a review. Cem. Concr. Res. 2019. 123, p. 105780, 10.1016/j.cemconres.2019.105780.
8. Kolchunov V.I., Kolchunov Vl.I., Fedorova N.V. Deformation models of reinforced concrete under special effects. Industrial and civil construction. 2018. No. 8. P. 54-60.
9. Feng P., Meng X., Chen J., Ye L. Mechanical properties of structures 3D printed with cementitious powders. Construction and Building Materials. 2015. Vol. 93, pp. 486–497. https://doi.org/10.1016/j.conbuildmat.2015.05.132.
10. Wolfs R.J.M., Bos F.P., Salet T.A.M. Hardened properties of 3D printed concrete: The influence of process parameters on interlayer adhesion. Cement and Concrete Research. 2019 Vol. 119, pp. 132–140. https://doi.org/10.1016/j.cemconres.2019.02.017.
11. Le T.T., Austin S.A., Lim S., Buswell R.A., Law R., Gibb A.G.F. Hardened properties of high-performance print-ing concrete. Cement and Concrete Research. 2012. Vol. 42. Iss. 3, pp. 558–566. https://doi.org/10.1016/j.cemconres.2011.12.003.
12. Adamtsevich A.O., Pustovgar A.P. Additive building production: study of the effect of anisotropy of the strength characteristics of concrete. Stroitelnye materialy. 2022. No. 9. P. 18–24. DOI: https://doi.org/10.31659/0585-430X-2022-806-9-18-24
13. Perelmuter A.V., Kabantsev O.V., Pichugin S.F. Fundamentals of the method of calculated limit states. M.: Publishing house SKAD SOFT, Publishing house ASV, 2019 – 240 p.
Review
For citations:
Kabantsev O.V., Karlin A.V. Features of the Concrete Structure of the Structural Element Made by Additive Technology. Reinforced concrete structures. 2023;1(1):55-63. (In Russ.)
Views:
291
Email this article 